Long Range Wireless Access Point / Client Bridge - EL-EOC-2610
The EOC-2610 is a high performance outdoor wireless Access Point and Client Bridge for the unlicensed 2.4GHz 802.11b/g range. It features high transmit output power and high receive sensitivity. The unit includes a 10bB antenna and can also be used with external antennas for maximum flexibility and is designed to be pole or wall mounted.
Configured as a wi-fi access point the 2610’s high output power and sensitivity extend coverage to reduce the number of Access Points required to cover a given area, minimising equipment and installation costs.
Configured in a pair for point to point bridging the 2610 can support distances up to 30km, using suitable external antennas. LED signal strength indicators are provided to aid alignment
The 2610 is also particularly suited to use as a low-cost customer premise client device in wireless ISP installations.
Wireless links are secured with 64/128-bit WEP and WPA/WPA2 data encryption and MAC address filtering lets you select exactly which stations are given access. In addition User-to-User Isolation can hide users from each other on public networks.
The attractive design, high performance and array of features make EOC-2610 an excellent wireless solution for your home or business.
- 2.4GHz It works in 2.4GHz frequency spectrum
- High Data Rate High speed physical transmitting rate up to 54Mbps with 11g, support large payload such as MEPG video streaming, Super G: 108Mbps
- Multifunction application Access Point/Client Bridge
- Long range transmitting Transmit power control and distance control (ACK timeout)
- Signal Strength LED indicators have the best transmit and receive signal for traffic communication
- Antenna Diversity Two internal panel antennas and also could switch to external antenna for applications
Networking
- Public wireless solution An AP interface that is especially useful in public areas such as hotspots and enterprise
- Signal Strength Display RF signal strength status shown LEDs of 3 colors, making network build-up easier
- QoS(WMM) Enhance performance and density (Phase 2)
Security
- 802.11i WEP, WPA-PSK (TKIP or AES), WPA2
- 802.1x IEEE 802.1x Supplicant support in CB mode
- MAC address functions MAC address filter (AP mode)
- L2 isolation
- Station isolation
- Wired separation
Management
- Firmware Upgrade Upgrading firmware via web browser, setting are reserved after upgrade
- Reset & Backup Reset to factory default. User can export all setting into a file via WEB
- MIB MIB I, MIB II(RFC1213)
- SNMP V1, V2c
Hardware Specification
Physical Interface
One 10/100 Fast Ethernet RJ-45
Reset Button
One ReSMA Connector
One switch (external and internal antenna switching)
LED indicators
Power/ Status
LAN (10/100Mbps)
WLAN (Wireless is up)
3* Link Quality (Client Bridge mode)
• Green: Good Quality
• Yellow: Marginally Acceptable Quality
• Red: Bad Quality
Power Requirements
Active Ethernet (Power over Ethernet, IEEE802.3af) 24V DC/1A
Proprietary PoE design
Channel Selection (Setting varies by countries)
Transmission Rate
11 b/g：54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 in Mbps
Distance Control : 1km to 30km
802.1x Ack timeout
Transmit power table
Signal Strength indication using LEDs
Security
WEP Encryption-64/128/152 bit
WPA Personal (WPA-PSK using TKIP or AES)
WPA Enterprise (WPA-EAP using TKIP)
802.1x Authenticator
Hide SSID in beacons
L2 isolation(AP mode)
Wireless STA (Client) connected list
VLAN pass through
QoS
WMM (Phase 2)
Management
Configuration
Web-based configuration (HTTP)
Firmware Upgrade
• Upgrade firmware via web-browser
• Keep latest setting when f/w update
Please wait while we sign you in...
