Discontinued Item

^

EL-EAP900 Rear View Monitor & Manage Several Access Points using the EZ Controller - free download

v


<<

>>

Click the image to enlarge

EL-EAP900H

EnGenius 11n Dual Band Concurrent Access Point/WDS/Repeater

  • 2.4GHz/5GHz - 450Mbps + 450Mbps
  • Ideal for covering WiFi deadspots
  • Supports Power over Ethernet
  • 3 different modes: Access Point, WDS AP, or WDS Bridge
  • Discreet styling
  • There is no separate power supply included*
  • 802.11k/r Roaming supported without the need for an AP Controller (latest firmware required)
  • Monitor & Manage Serveral Access Points using EZ Controller - free download

 

Authorised Distributor

»

EL-EAP900H

(Mfr part code: EAP900H)


Overview

The EAP900H is equipped with two powerful independent RF interfaces that support 2.4GHz 802.11b/g/n (3T3R) and 5GHz 802.11a/n (3T3R), offering bandwidth up to 450Mbps + 450Mbps to accommodate traffic-intensive applications such as multimedia streaming.

Each radio in the EAP900H has been enhanced to provide higher signal strength and receive sensitivity; this will help reduce dead spots in your network and boost received signal quality on both ends of Access Point and wireless client devices.

The EAP900H can be powered by the enclosed power adapter or any 802.3at-compliant PoE switches; solving common power sourcing issue in the field where devices are usually placed at in dropped-ceilings or mounted on walls.

Each radio of the EAP900H can independently operate in 3 different modes, namely Access Point, WDS AP, or WDS Bridge; this will allow multiple combinations of operation modes on a single device.

Besides intuitive web-based management, the EnGenius EZ Controller software utility gives you the added convenience of applying various configuration settings into devices, enabling prompt WLAN deployment and configuration update. For effective spectrum usage, the EAP900H has enclosed band steering technology, enabling 5GHz-capable clients to associate with its 5GHz radio and
offloading air utilization in 2.4GHz-band. In addition, EnGenius fast roaming minimizes service down-time during handoff from one base station to another.

EZ Controller
Simplified AP Monitoring and Management

For easier monitoring and maintenance after deployment on rooftops and other hard to reach places, users can monitor the Access Point remotely with SNMP-based EZ Controller wireless Access Point software for Windows, Mac OSX, and Linux.

EZ Controller Screen

Free Download - click here

 

Specifications

Download specification datasheet (includes radiation patterns)
Hardware Specifications
MCU Atheros QCA9558
RF Atheros QCA9558 (2.4GHz) + QCA9580 (5GHz)
Memory 256MB
Flash 16MB
Physical Interface 1 x 10/100/1000 BASE-T Ethernet (RJ45) with 802.3at PoE
1 x DC power connector
1 x reset button
Power Requirements

DC Input: 12VDC/2A
PoE: Compatible with 802.3at
Average Watt 10.22
Peak Watt 18.24

 

*Please note that the DC power supply is not included with this product.
Since this product is normally used in a ceiling or wall mounted application then PoE is the most common power method so a DC power adapter is unlikely to be used. If you plan to power the unit directly then you will need to purchase the power supply, listed in the accessories, relevant to your country.

Wireless Specification
Frequency Band

802.11a/b/g/n

Available transmit power (ERIP) 19dBm
Data rate 450Mbps(2.4GHz) 450Mbps (5GHz)
Operation Mode Access Point / WDS AP/ WDS Bridge / Repeater
Wireless/Network Auto Channel Selection Setting varies by regulatory domains
Supports up to 8 SSIDs per frequency band
VLAN Tag / VLAN Pass-through
Wireless Client List
Supports 802.11e/WMM
Traffic Shaping
Guest Network - Allocates a separate network segment for guest access within the
same WLAN
Band Steering - Moves 5GHz-compatible clients to 5GHz band to ease traffic
congestion on 2.4GHz band
Fast Handover
Security WEP encryption: 64/128/152-bit
WPA/WPA2 Enterprise/PSK
Hidden SSID
MAC address filtering (up to 50 MAC)
Station separation
Management Web interface (HTTP/S)
SNMP v1/v2c/v3 with MIB I/II and private MIB
CLI (Telnet/SSH)
Firmware Upgrade
Web interface or CLI
Backup / Restore Settings
Revert to factory default settings
Save Configuration as Default:
Saves the customized configuration as default
Auto Reboot
Specifies interval to reboot system periodically
E-mail Alert / Syslog Notification
Environmental & Mechanical
Temperature Range 0 to 40° C - Operating, -20 to 60 ° C - Storage
Humidity (non-condensing) 0%~90% typical
Dimensions 161.5mm(D) x 41.5mm (H)
Weight 290g

Downloads

Firmware for this product should only be sourced via the Solwise or EnGenius Networks Europe B.V. websites. If it is sourced elsewhere it may damage your device and invalidate the warranty. We can't provide service support to devices which are not running with ETSI firmware. EnGenius Networks Europe B.V. Downloads Site 27.10.16

EZ Controller
Simplified AP Monitoring & Management

For easier monitoring and maintenance after deployment on rooftops and other hard to reach places, users can monitor the Access Point remotely with SNMP-based EZ Controller wireless Access Point software for Windows, Mac OSX, and Linux.

Free Download 27.04.15
User Manual Download here 19.05.15
Firmware Ver 2.1.257 Download here 08.08.16
Firmware Ver 2.0.8 Download here 07.02.14

Press Reviews

Videos

Accessories


<

>

X