Click the image to enlarge
EnGenius Dual Band Wireless N600 Managed Indoor Access Point
- Supports IEEE 802.11a/b/g/n standards with up to a 300 Mbps data rate on each band
- Up to 29 dBm high RF power on 2.4 GHz. Up to 26 dBM on 5 GHz for longer range, enhanced wireless coverage
- Dynamic Channel Optimisation
- Designed for indoor ceiling or desktop deployments
- 4 internal MIMO antennas / Dual-band
- Band Steering shifts Dual-band clients to 5 GHz for better throughput performance
- Fast roaming, Fast Handover
- 802.11k/r Roaming supported without the need for an AP Controller (latest firmware required)
- There is no separate power supply included*
- Register for your Limited Lifetime Warranty
The Neutron Series
Wireless Management Solution
The EnGenius Neutron Series of wireless management products can be mixed and matched to create ideal wireless connectivity solutions for hotels, resorts, high schools, universities, corporate campuses, sports stadiums and arenas and for other companies and organizations.
This is a scalable solution for operations that occupy large properties and that need to deploy, monitor, and manage numerous EnGenius EWS Wireless Access Points from one simple and accessible browser-based software platform. EWS Switches can support any small number of EWS Wireless Access Points to several hundred depending on the number of EWS Switches in the network.
The EWS310AP can operate as a stand-alone Access Point connecting to third-party PoE-capable switches but more control and versatile management of the Access Point is achievable when it is part of an EnGenius Neutron Series wireless network management solution because the AP includes firmware that enables it to be immediately discovered, configured, monitored and managed from a compatible Neutron Series PoE+ Switch (EWS5912FP, EWS7928FP or EWS7952FP).
This capability enables IT managers to deploy and manage up to 50 EWS310APs from Neutron Series Switch allowing for simplified management from one browser-based interface including simultaneous firmware upgrades, clustering, traffic monitoring, bandwidth steering and many other features that can be reset or reconfigured from the convenience of the IT manager’s desktop.
Operating in both the 2.4 GHz and 5 GHz frequency spectrums and supporting 802.11a/b/g/n standards the EWS310P features wireless speeds up to 300 Mbps on each radio, a Gigabit port for connecting to 802.3at/af-capable PoE Switches, and an enhanced receive sensitivity MIMO (Multiple In / Multiple Out) antenna array. As a result, the EWS310AP is ideal for spacious environments such as large homes, small and medium-sized businesses, multiple-floor offices, hotels, hospitals, and other multi-floor buildings.
As the EWS310AP is designed for deployments on desktops or on ceilings where power outlets may be scarce, it also comes equipped with PoE (Power-over-Ethernet) IEEE 802.3at/af for use with an 802.3at/af-capable PoE injector or 802.3at/af-capable PoE Switches, drawing up to 15.6 watts of power.
Paired with other Neutron Series Access Points and Switches, the EWS310AP helps to make managing a network easier with its standardized GUI. To protect sensitive data during wireless transmissions, the EWS310AP offers different industry-standard encryption settings for wireless transmissions, including WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA Enterprise, WPA2 Enterprise, and WPA2 Mixed Enterprise. It also includes MAC address filtering to allow network administrators to offer network access only to verified computers and devices based on their MAC addresses.
Neutron Series Access Point
Can be configured, managed and monitored with several Neutron Series Access Points from the browser-based interface of one Neutron Series Wireless Management PoE+ Switch. After a Neutron Series Layer PoE+ Switch discovers the EWS310AP it can be "added" and set to be "managed" by the Switch. The Neutron Wireless Management solution supports bulk firmware upgrades and other features that can be set and managed across deployed Neutron Series Access Points simultaneously.
Up to 300 Mbps on each of the 2.4 and 5 GHz frequency bands for faster file transfers and smoother video streaming.
Dual-Band for Expanded User Capacity
802.11n concurrent Dual-band operation in the 2.4 GHz and 5 GHz. Can support up to 100+ users (1)
High Power, Long-Range and Multiple Floor Penetration
Up to 29 dBm on the 2.4 GHz band and up to 26 dBm on the 5 GHz band provides more than twice the wireless coverage over mainstream competitors and enables the wireless signal to penetrate floors, ceilings, and walls for greater device connectivity. Internal MIMO antenna array provides better reception and performance as clients change their orientation.
Can be configured to broadcast up to 16 SSIDs (8 SSIDs per frequency band). Each SSID can be tagged to a specified network VLAN for different user access tiers based on established access rights.
1- User capacity performance results may vary based on topology configuration, structural and architectural elements, environmental factors, type of data traffic, RF capabilities of client devices, distance, RF interference in the operating environment and other factors.
RF: 2.4 and 5 GHz Frequency Bands
Standard: IEEE 802.11a/b/g/n
Radio I: 11b/g/n: 2.412~2.484 GHz
Radio II: 11a/n: 5.18-5.24 and 5.26-5.32 and 5.5-5.7 and 5.745-5.825 GHz
Data Rate: Up to 300 Mbps in both frequency bands
Flash Memory: 16MB
|Antenna||Four (4) Internal 5 dBi Omni-Directional Antennas|
1 x RJ-45 Gigabit Ethernet (10/100/1000 Mbps) - PoE capable
1 x Reset Button
1 x Power Connector
DC Input: 12VDC/2A
*Please note that the DC power supply is not included with this product.
|Modulations||OFDM: BPSK, QPSK, 26-OAM, 64-QAM, DBPSK, DQPSK, CCK|
2.4 GHz: US/Canada 1-11
5 GHz: Country dependent for the following ranges:
36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
|Operation Modes||Access Point|
|Multiple BSSID||Supports up to 8 BSSIDs per radio|
|LAN||IP (check validity and DHCP server IP range) MAC|
|SSID-to-VLAN Tagging||Supports 802.1q SSID-to-VLAN tagging|
|Spanning Tree||Supports 802.1d Spanning Tree Protocol|
Wireless Mode: 11a/11b/11g/11n
Channel selection (settings vary by country)
Channel bandwidth (Auto, 20 MHz, 40 MHz)
|QoS||WMM (Wireless Multimedia)|
Wireless Management Features (with Neutron Series Switch)
• Access Point Auto Discovery and Provisioning
• Access Point Auto IP Assignment
• Access Point Cluster Management
• Remote Access Point Rebooting
• Access Point Device Name Editing
• Access Point Radio Settings
• Band Steering
• Traffic Shaping
• Fast Handover
• Fast roaming (requires RADIUS server)
• Access Point Client Limiting
• Wireless Security (WEP, WPA/WPA2 Enterprise, WPA/WPA2 PSK)
• VLANs for Access Point- Multiple SSIDs
• Guest Network
• Access Point Status Monitoring
• Wireless Client Monitoring
• Wireless Traffic & Usage Statistics
• Visual Topology View
• Floor Plan View
• Map View
• Secure Control Messaging
• SSL Certificate
• Local MAC Address Database
• Remote MAC Address Database (RADIUS)
• Unified Configuration Import / Export
• Bulk Firmware Upgrade Capability
• Intelligent Diagnostics
|Environmental & Physical|
Operating: 0 to 50ºC (32º to 122ºF)
Operating humidity: 0 to 90º
Storage temperature: -20ºC to 60ºC (-4Fº to 140ºF)
|Certifications||FCC, IC, CE|
|Dimensions & Weights|
Weight, Diameter, Height
Weight: 363 g.
EWS310AP Dual Band N600 Indoor Access Point
T-Rail Mounting Kit
Ceiling Mount and Wall Screw Kit
RJ-45 Ethernet Cable
Quick Installation Guide
|Firmware for this product should only be sourced via the Solwise or EnGenius Networks Europe B.V. websites. If it is sourced elsewhere it may damage your device and invalidate the warranty. We can't provide service support to devices which are not running with ETSI firmware.||EnGenius Networks Europe B.V. Downloads Site||27.10.16|
|Neutron Quick Start Guide||Download here||01.09.16|
|High Resolution Images||Download here||24.06.16|
|Fimware Ver 2.0.290||Download here||08.08.16|
|Roaming with the EnGenius Neutron Managed Solution||Download here||20.05.15|
|EWS Phase 2 Firmware: this is available though the One-Click Update feature of the management switch
Wireless Client Fingerprinting
|Download Application Notes||14.04.15|
|User Manual :
EWS210AP / EWS310AP / EWS320AP / EWS360AP
|Quick Installation Guide
EWS310AP / EWS320AP / EWS360AP
|FCC Report||Download here||19.06.14|
|CE Certificate||Download here||01.07.15|
|CE Report||Download here||19.06.14|